Carbon monoxide & smoke alarm Kidde 10SCO
- Stock: In Stock
- Model: KID-10SCO
- EAN: 0047871104062
- Weight: 360g
- Dimensions: 145mm x 145mm x 45mm
10SCO is used to protect rooms against fire and carbon monoxide. The device has two independent sensors placed in one housing.
Smoke sensor monitors the air for the presence of products formed during combustion or smoldering objects. Carbon monoxide sensor is used to monitor rooms for carbon monoxide (CO).
If a fire is detected and / or the permissible concentration of carbon monoxide is exceeded, an acoustic alarm with a strength of 85dB is triggered, an optical alarm (red LED) and a voice message (in English) is emitted informing about the type of detected threat. The built-in automatic efficiency control system monitors, among others state of sensors, batteries and internal circuits. When a fault is detected, the signaling appropriate to the fault is activated.
Test / Reset button allows the device to be checked and operated. The device's memory stores information about the detection of CO concentration exceeding 100 PPM. Thanks to this, the user can check if there was any emission of carbon monoxide during his absence in the room.
10SCO can be ceiling or wall mounted. Battery power allows the detector to be installed in the most optimal place and provides protection also in the event of a power failure in the network. 10 years after the activation of the power supply, device will inform about the need to replace the device.
10SCO is a device that meets both the PN-EN14604: 2006P (EN14604: 2005) standard for home smoke detectors and the PN-EN50291-1: 2010 / A1: 2013-05 standard for home carbon monoxide detectors. Fulfilling the above-mentioned standards has been confirmed by an independent, notified testing body, BSI.
Recommended installation locations: near the kitchen, in the living room, living room, dining room, bedroom, basement, in the attic, and places where electrical appliances that may be a source of fire and appliances that are a potential source of carbon monoxide, e.g. fireplace, electric or gas heaters rooms, etc.
ADVANTAGES
- Electrochemical technology - one of the most precise electrochemical sensors in the world
- High-quality optical sensor ensuring long-term and stable operation
- At least 40% longer service life compared to most sensors available on the market
- Loud alarm signaling
- Voice prompts distinguishing the detected threat
- Test / Reset button for checking and operating the device
- Hush® feature to mute the audible alarm signal
- Battery powered for protection also in the event of a power failure in the network
- Can be mounted on the ceiling or wall
- Safety mechanism against accidental disassembly of the sensor and battery
- Signaling of discharged batteries
- Signaling of incorrect operation and end of the period of operation
- Simple assembly and operation
- Compliance with PN-EN14604: 2006P (EN14604: 2005)
- Compliance with the PN-EN50291-1: 2010 / A1: 2013-05 standard
- 10-year warranty
Product information | |
Sensor | Optical for fire hazard detection KIDDE electrochemical CO sensor for the detection of carbon monoxide |
Alarm signaling | Exceeding the permissible CO concentration - acoustic 85dB, optical (red LED) and voice message "Warning! Carbon Monoxide" Fire detection - acoustic 85dB, optical (red LED) and "Fire! Fire!" Voice message Save concentrations above 100 PPM in the memory - green LED blinking every 16 seconds |
Signaling the end of the service life | Yes - a short beep every 30 seconds |
Signaling of incorrect operation | Short beep and flashing every 30 seconds. red LED |
Test / Reset Button | For controlling and operating the device and resetting alarm signals |
Sensor durability | 10 years |
Mounting | Wall or ceiling mounted |
Housing | Made of ABS plastic |
Additionally included | Battery, mounting bracket, mounting pins, user manual |
Power | |
Power source | 9V alkaline battery (included) |
Battery discharge indication | Short beep and flashing every 30 seconds. red LED, voice announcement "Low Battery" |
Working and storage conditions | |
Working conditions | Temperature: 0 ~ 40°C Humidity: up to 90% RH, non-condensing |
Storage conditions | Temperature: -10 ~ 60°C Humidity: up to 90% RH, non-condensing |
Quality and safety | |
Certificates and approvals | PN-EN50291-1:2010/A1:2013-05, BSI certification body PN-EN14604:2006P (EN14604:2005), BSI certification body CE 0086-CPD-535595 14 |
Warranty | 10 years |